医用高压灭菌锅HVE-50操作使用规程说明及注意事项

医用高压灭菌锅HVE-50操作使用规程说明，更多分析仪器维修保养知识请查看仪器无忧网维修保养笔记。

高压灭菌锅HVE-50操作步骤：

1．插上电源插头，打开开关，按“POWER ON/OFF”键开启电源。

2．确认压力表读数为0，将LOCK/UNLOCK杆推向右边，打开盖子，加水2升左右（可通过底盘中心小孔观察水位，灭菌腔每天需换水一次）。

3．确认排汽瓶中的水位界于HIGH和LOW之间，否则取出该塑料瓶倒水或加水若干。

4．装入待灭菌物，盖上盖子，将LOCK/UNLOCK杆推向左边。（连续灭菌时，第2次操作前请确保灭菌腔温度已降至50℃以下。）

5．按“MODE”键选择工作模式，根据需要检查和修改温度、时间设定值。

6．按“START/STOP”键，仪器即开始灭菌过程。若确实需要停止灭菌，再按该键一次仪器即退回待机状态。

7．灭菌完毕，待温度下降，压力表读数为0时，将LOCK/UNLOCK杆推向右边，打开盖子。（保温状态时需先按“START/STOP”停止运行。若仪器进入节电模式需先按任意键恢复面板显示后方可进行其它操作）。

8．取出灭菌物（小心避免蒸汽及灭菌物烫伤手脸）。

9．按“POWER ON/OFF”键关闭电源，断开开关，拔下插头。待仪器充分冷却后，擦干表面冷凝水，并进行灭菌腔排水。

注意事项：

1．灭菌锅必须加纯水，以防止产生大量水垢。

2．本仪器系高温高压自动灭菌设备，除特别注意事项外，普通高压灭菌器所要求的常规操作规范对于本仪器的操作同样必须遵循。

3.本仪器不可用于腐蚀性、易燃、易爆和热压不稳定等物品的灭菌。

4．灭菌器盖子仅当仪器通电且温度下降、压力表读数为0时方可开启，不可强行用力打开，以免仪器损坏和发生意外伤害事故。

5．操作过程谨防蒸汽和灭菌物品烫伤。

6．仪器较长时间不用，请务必将灭菌腔排水，并保证腔体清洁干燥。

7．及时取走自己的物品，注意用电安全，保持实验室清洁，不浪费。仪器不正常时，及时上报，不得自行处理。

Steps:

1. Plug in the power plug, turn on the switch, and press the “POWER ON/OFF” button to turn on the power.

2. Confirm that the pressure gauge reading is 0, push the LOCK/UNLOCK rod to the right, open the lid, add about 2 liters of water (the water level can be observed through the small hole in the center of the chassis, and the sterilization chamber needs to change the water once a day).

3. Make sure that the water level in the exhaust bottle is between HIGH and LOW, otherwise remove the plastic bottle to pour water or add some water.

4. Load the object to be sterilized, close the lid and push the LOCK/UNLOCK rod to the left. (When continuously sterilizing, make sure that the temperature of the sterilization chamber has dropped below 50 °C before the second operation.)

5. Press the “MODE” button to select the working mode and check and modify the temperature and time settings as needed.

6. Press the “START/STOP” button and the instrument will start the sterilization process. If it is really necessary to stop the sterilization, press the button again to return the instrument to the standby state.

7. After the sterilization is completed, when the temperature drops and the pressure gauge reads 0, push the LOCK/UNLOCK lever to the right to open the cover. (In the warm-up state, you need to press “START/STOP” to stop running. If the instrument enters the power-saving mode, you need to press any key to restore the panel display before you can perform other operations).

8. Remove the sterilized material (be careful to avoid steam and sterilizing burns on your face).

9. Press the “POWER ON/OFF” button to turn off the power, disconnect the switch, and remove the plug. After the instrument is sufficiently cooled, the surface condensed water is wiped dry and the sterilization chamber is drained.

{来源|仪器无忧网，根据专业书籍以及网络资料编辑创作、转载需联系我们授权}

上一篇:全自动智能一体化蒸馏仪使用保养

下一篇:积分声级计应用领域及使用保养维修